/****************************************************************************** * * Microchip Memory Disk Drive File System * ****************************************************************************** * FileName: HardwareProfile.h * Dependencies: None * Processor: PIC18/PIC24/dsPIC30/dsPIC33/PIC32 * Compiler: C18/C30/C32 * Company: Microchip Technology, Inc. * * Software License Agreement * * The software supplied herewith by Microchip Technology Incorporated * (the ？Company？) for its PICmicro？ Microcontroller is intended and * supplied to you, the Company？s customer, for use solely and * exclusively on Microchip PICmicro Microcontroller products. The * software is owned by the Company and/or its supplier, and is * protected under applicable copyright laws. All rights are reserved. * Any use in violation of the foregoing restrictions may subject the * user to criminal sanctions under applicable laws, as well as to * civil liability for the breach of the terms and conditions of this * license. * * THIS SOFTWARE IS PROVIDED IN AN ？AS IS？ CONDITION. NO WARRANTIES, * WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED * TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A * PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. THE COMPANY SHALL NOT, * IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL OR * CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER. * *****************************************************************************/ /******************************************************************** Change History: Rev Description ---- ----------------------- 1.3.4 Added support for PIC18F8722,PIC24FJ256DA210, dsPIC33E & PIC24E microcontrollers. Added macro "SPI_INTERRUPT_FLAG_ASM" for PIC18F microcontrollers to support SD card SPI driver. ********************************************************************/ #ifndef _HARDWAREPROFILE_H_ #define _HARDWAREPROFILE_H_ // Define your clock speed here // Sample clock speed for PIC18 #if defined (__18CXX) #if defined(__18F87J50) #define DEMO_BOARD PIC18F87J50_PIM #define PIC18F87J50_PIM #define GetSystemClock() 48000000 // System clock frequency (Hz) #elif defined(__18F46J50) #define DEMO_BOARD PIC18F46J50_PIM #define PIC18F46J50_PIM #define GetSystemClock() 48000000 // System clock frequency (Hz) #elif defined(__18F8722) #define GetSystemClock() 40000000 // System clock frequency (Hz) #endif #define GetPeripheralClock() GetSystemClock() // Peripheral clock freq. #define GetInstructionClock() (GetSystemClock() / 4) // Instruction clock freq. // Sample clock speed for a 16-bit processor #elif defined (__PIC24F__) #define GetSystemClock() 32000000 #define GetPeripheralClock() GetSystemClock() #define GetInstructionClock() (GetSystemClock() / 2) // Clock values #define MILLISECONDS_PER_TICK 10 // Definition for use with a tick timer #define TIMER_PRESCALER TIMER_PRESCALER_8 // Definition for use with a tick timer #define TIMER_PERIOD 20000 // Definition for use with a tick timer #elif defined (__dsPIC33F__) #define GetSystemClock() 80000000 #define GetPeripheralClock() (GetSystemClock() / 2) #define GetInstructionClock() (GetSystemClock() / 2) // Clock values #define MILLISECONDS_PER_TICK 10 // Definition for use with a tick timer #define TIMER_PRESCALER TIMER_PRESCALER_64 // Definition for use with a tick timer #define TIMER_PERIOD 6250 // Definition for use with a tick timer #elif defined (__dsPIC33E__) || defined (__PIC24E__) #define GetSystemClock() 120000000 #define GetPeripheralClock() (GetSystemClock() / 2) #define GetInstructionClock() (GetSystemClock() / 2) // Clock values #define MILLISECONDS_PER_TICK 10 // Definition for use with a tick timer #define TIMER_PRESCALER TIMER_PRESCALER_64 // Definition for use with a tick timer #define TIMER_PERIOD 9375 // Definition for use with a tick timer // Sample clock speed for a 32-bit processor #elif defined (__PIC32MX__) // Indicates that the PIC32 clock is running at 48 MHz //#define RUN_AT_48MHZ // Indicates that the PIC32 clock is running at 24 MHz //#define RUN_AT_24MHZ // Indicates that the PIC32 clock is running at 80 MHz #define RUN_AT_80MHZ // Various clock values #if defined(RUN_AT_48MHZ) #define GetSystemClock() 48000000UL // System clock frequency (Hz) #define GetPeripheralClock() 48000000UL // Peripheral clock frequency #define GetInstructionClock() (GetSystemClock()) // Instruction clock frequency #elif defined(RUN_AT_24MHZ) #define GetSystemClock() 24000000UL #define GetPeripheralClock() 24000000UL #define GetInstructionClock() (GetSystemClock()) #elif defined(RUN_AT_80MHZ) #define GetSystemClock() (80000000ul) #define GetPeripheralClock() (GetSystemClock()/2) #define GetInstructionClock() (GetSystemClock()) #else #error Choose a speed #endif // Clock values #define MILLISECONDS_PER_TICK 10 // Definition for use with a tick timer #define TIMER_PRESCALER TIMER_PRESCALER_8 // Definition for use with a tick timer #define TIMER_PERIOD 37500 // Definition for use with a tick timer #endif // Select your interface type // This library currently only supports a single physical interface layer at a time // Description: Macro used to enable the SD-SPI physical layer (SD-SPI.c and .h) #define USE_SD_INTERFACE_WITH_SPI // Description: Macro used to enable the CF-PMP physical layer (CF-PMP.c and .h) //#define USE_CF_INTERFACE_WITH_PMP // Description: Macro used to enable the CF-Manual physical layer (CF-Bit transaction.c and .h) //#define USE_MANUAL_CF_INTERFACE // Description: Macro used to enable the USB Host physical layer (USB host MSD library) //#define USE_USB_INTERFACE /*********************************************************************/ /******************* Pin and Register Definitions ********************/ /*********************************************************************/ /* SD Card definitions: Change these to fit your application when using an SD-card-based physical layer */ #ifdef USE_SD_INTERFACE_WITH_SPI #ifdef PIC18F87J50_PIM #define USE_PIC18 #define USE_SD_INTERFACE_WITH_SPI #define INPUT_PIN 1 #define OUTPUT_PIN 0 // Chip Select Signal #define SD_CS LATBbits.LATB3 #define SD_CS_TRIS TRISBbits.TRISB3 // Card detect signal #define SD_CD PORTBbits.RB4 #define SD_CD_TRIS TRISBbits.TRISB4 // Write protect signal #define SD_WE PORTAbits.RA4 #define SD_WE_TRIS TRISAbits.TRISA4 // Registers for the SPI module you want to use // Description: The main SPI control register #define SPICON1 SSP1CON1 // Description: The SPI status register #define SPISTAT SSP1STAT // Description: The SPI buffer #define SPIBUF SSP1BUF // Description: The receive buffer full bit in the SPI status register #define SPISTAT_RBF SSP1STATbits.BF // Description: The bitwise define for the SPI control register (i.e. _____bits) #define SPICON1bits SSP1CON1bits // Description: The bitwise define for the SPI status register (i.e. _____bits) #define SPISTATbits SSP1STATbits // Description: The interrupt flag for the SPI module #define SPI_INTERRUPT_FLAG PIR1bits.SSPIF #define SPI_INTERRUPT_FLAG_ASM PIR1, 3 // Description: The enable bit for the SPI module #define SPIENABLE SSPCON1bits.SSPEN // Defines for the HPC Explorer board #define SPICLOCK TRISCbits.TRISC3 #define SPIIN TRISCbits.TRISC4 #define SPIOUT TRISCbits.TRISC5 // Latch pins for SCK/SDI/SDO lines #define SPICLOCKLAT LATCbits.LATC3 #define SPIINLAT LATCbits.LATC4 #define SPIOUTLAT LATCbits.LATC5 // Port pins for SCK/SDI/SDO lines #define SPICLOCKPORT PORTCbits.RC3 #define SPIINPORT PORTCbits.RC4 #define SPIOUTPORT PORTCbits.RC5 // Will generate an error if the clock speed is too low to interface to the card #if (GetSystemClock() < 400000) #error System clock speed must exceed 400 kHz #endif #elif defined(__18F8722) #define USE_PIC18 #define USE_SD_INTERFACE_WITH_SPI #define INPUT_PIN 1 #define OUTPUT_PIN 0 // Chip Select Signal #define SD_CS PORTBbits.RB3 #define SD_CS_TRIS TRISBbits.TRISB3 // Card detect signal #define SD_CD PORTBbits.RB4 #define SD_CD_TRIS TRISBbits.TRISB4 // Write protect signal #define SD_WE PORTAbits.RA4 #define SD_WE_TRIS TRISAbits.TRISA4 // Registers for the SPI module you want to use #define SPICON1 SSP1CON1 #define SPISTAT SSP1STAT #define SPIBUF SSP1BUF #define SPISTAT_RBF SSP1STATbits.BF #define SPICON1bits SSP1CON1bits #define SPISTATbits SSP1STATbits #define SPI_INTERRUPT_FLAG PIR1bits.SSPIF // Defines for the HPC Explorer board #define SPICLOCK TRISCbits.TRISC3 #define SPIIN TRISCbits.TRISC4 #define SPIOUT TRISCbits.TRISC5 // Latch pins for SCK/SDI/SDO lines #define SPICLOCKLAT LATCbits.LATC3 #define SPIINLAT LATCbits.LATC4 #define SPIOUTLAT LATCbits.LATC5 // Port pins for SCK/SDI/SDO lines #define SPICLOCKPORT PORTCbits.RC3 #define SPIINPORT PORTCbits.RC4 #define SPIOUTPORT PORTCbits.RC5 #define SPIENABLE SSPCON1bits.SSPEN #define SPI_INTERRUPT_FLAG_ASM PIR1, 3 // Will generate an error if the clock speed is too low to interface to the card #if (GetSystemClock() < 400000) #error System clock speed must exceed 400 kHz #endif //PM #elif defined PIC18F46J50_PIM #define USE_PIC18 #define USE_SD_INTERFACE_WITH_SPI #define INPUT_PIN 1 #define OUTPUT_PIN 0 #define USE_SD_INTERFACE_WITH_SPI #define TRIS_CARD_DETECT TRISBbits.TRISB4 // Input #define CARD_DETECT PORTBbits.RB4 #define TRIS_WRITE_DETECT TRISDbits.TRISD7 // Input #define WRITE_DETECT PORTDbits.RD7 // Chip Select Signal #define SD_CS PORTBbits.RB3 #define SD_CS_TRIS TRISBbits.TRISB3 // Card detect signal #define SD_CD PORTBbits.RB4 #define SD_CD_TRIS TRISBbits.TRISB4 // Write protect signal #define SD_WE PORTDbits.RD7 #define SD_WE_TRIS TRISDbits.TRISD7 // TRIS pins for the SCK/SDI/SDO lines #define SPICLOCK TRISBbits.TRISB1 #define SPIIN TRISAbits.TRISA1 #define SPIOUT TRISAbits.TRISA5 // Latch pins for SCK/SDI/SDO lines #define SPICLOCKLAT LATBbits.LATB1 #define SPIINLAT LATAbits.LATA1 #define SPIOUTLAT LATAbits.LATA5 // Port pins for SCK/SDI/SDO lines #define SPICLOCKPORT PORTBbits.RB1 #define SPIINPORT PORTAbits.RA1 #define SPIOUTPORT PORTAbits.RA5 // Registers for the SPI module you want to use #define SPICON1 SSP2CON1 #define SPISTAT SSP2STAT #define SPIBUF SSP2BUF #define SPISTAT_RBF SSP2STATbits.BF #define SPICON1bits SSP2CON1bits #define SPISTATbits SSP2STATbits #define SPI_INTERRUPT_FLAG PIR3bits.SSP2IF #define SPIENABLE SSP2CON1bits.SSPEN #define SPI_INTERRUPT_FLAG_ASM PIR1, 3 // Will generate an error if the clock speed is too low to interface to the card #if (GetSystemClock() < 400000) #error System clock speed must exceed 400 kHz #endif #elif defined __PIC24F__ #if defined (__PIC24FJ64GA002__) // Description: SD-SPI Chip Select Output bit #define SD_CS LATBbits.LATB4 // Description: SD-SPI Chip Select TRIS bit #define SD_CS_TRIS TRISBbits.TRISB4 // Description: SD-SPI Card Detect Input bit #define SD_CD PORTBbits.RB8 // Description: SD-SPI Card Detect TRIS bit #define SD_CD_TRIS TRISBbits.TRISB8 // Description: SD-SPI Write Protect Check Input bit #define SD_WE PORTBbits.RB9 // Description: SD-SPI Write Protect Check TRIS bit #define SD_WE_TRIS TRISBbits.TRISB9 // Registers for the SPI module you want to use // Description: The main SPI control register #define SPICON1 SPI1CON1 // Description: The SPI status register #define SPISTAT SPI1STAT // Description: The SPI Buffer #define SPIBUF SPI1BUF // Description: The receive buffer full bit in the SPI status register #define SPISTAT_RBF SPI1STATbits.SPIRBF // Description: The bitwise define for the SPI control register (i.e. _____bits) #define SPICON1bits SPI1CON1bits // Description: The bitwise define for the SPI status register (i.e. _____bits) #define SPISTATbits SPI1STATbits // Description: The enable bit for the SPI module #define SPIENABLE SPISTATbits.SPIEN // Tris pins for SCK/SDI/SDO lines // Description: The TRIS bit for the SCK pin #define SPICLOCK TRISBbits.TRISB6 // Description: The TRIS bit for the SDI pin #define SPIIN TRISBbits.TRISB7 // Description: The TRIS bit for the SDO pin #define SPIOUT TRISBbits.TRISB5 #elif defined (__PIC24FJ128GA010__) // Description: SD-SPI Chip Select Output bit #define SD_CS LATBbits.LATB1 // Description: SD-SPI Chip Select TRIS bit #define SD_CS_TRIS TRISBbits.TRISB1 // Description: SD-SPI Card Detect Input bit #define SD_CD PORTFbits.RF0 // Description: SD-SPI Card Detect TRIS bit #define SD_CD_TRIS TRISFbits.TRISF0 // Description: SD-SPI Write Protect Check Input bit #define SD_WE PORTFbits.RF1 // Description: SD-SPI Write Protect Check TRIS bit #define SD_WE_TRIS TRISFbits.TRISF1 // Registers for the SPI module you want to use // Description: The main SPI control register #define SPICON1 SPI1CON1 // Description: The SPI status register #define SPISTAT SPI1STAT // Description: The SPI Buffer #define SPIBUF SPI1BUF // Description: The receive buffer full bit in the SPI status register #define SPISTAT_RBF SPI1STATbits.SPIRBF // Description: The bitwise define for the SPI control register (i.e. _____bits) #define SPICON1bits SPI1CON1bits // Description: The bitwise define for the SPI status register (i.e. _____bits) #define SPISTATbits SPI1STATbits // Description: The enable bit for the SPI module #define SPIENABLE SPISTATbits.SPIEN // Tris pins for SCK/SDI/SDO lines // Description: The TRIS bit for the SCK pin #define SPICLOCK TRISFbits.TRISF6 // Description: The TRIS bit for the SDI pin #define SPIIN TRISFbits.TRISF7 // Description: The TRIS bit for the SDO pin #define SPIOUT TRISFbits.TRISF8 #elif defined (__PIC24FJ256GB110__) // Description: SD-SPI Chip Select Output bit #define SD_CS LATBbits.LATB1 // Description: SD-SPI Chip Select TRIS bit #define SD_CS_TRIS TRISBbits.TRISB1 // Description: SD-SPI Card Detect Input bit #define SD_CD PORTFbits.RF0 // Description: SD-SPI Card Detect TRIS bit #define SD_CD_TRIS TRISFbits.TRISF0 // Description: SD-SPI Write Protect Check Input bit #define SD_WE PORTFbits.RF1 // Description: SD-SPI Write Protect Check TRIS bit #define SD_WE_TRIS TRISFbits.TRISF1 // Registers for the SPI module you want to use // Description: The main SPI control register #define SPICON1 SPI1CON1 // Description: The SPI status register #define SPISTAT SPI1STAT // Description: The SPI Buffer #define SPIBUF SPI1BUF // Description: The receive buffer full bit in the SPI status register #define SPISTAT_RBF SPI1STATbits.SPIRBF // Description: The bitwise define for the SPI control register (i.e. _____bits) #define SPICON1bits SPI1CON1bits // Description: The bitwise define for the SPI status register (i.e. _____bits) #define SPISTATbits SPI1STATbits // Description: The enable bit for the SPI module #define SPIENABLE SPISTATbits.SPIEN // Tris pins for SCK/SDI/SDO lines // Description: The TRIS bit for the SCK pin #define SPICLOCK TRISBbits.TRISB0 // Description: The TRIS bit for the SDI pin #define SPIIN TRISDbits.TRISD2 // Description: The TRIS bit for the SDO pin #define SPIOUT TRISFbits.TRISF8 #elif defined(__PIC24FJ256DA210__) // Description: SD-SPI Chip Select Output bit #define SD_CS PORTGbits.RG6 // Description: SD-SPI Chip Select TRIS bit #define SD_CS_TRIS TRISGbits.TRISG6 // Description: SD-SPI Card Detect Input bit #define SD_CD PORTAbits.RA15 // Description: SD-SPI Card Detect TRIS bit #define SD_CD_TRIS TRISAbits.TRISA15 // Description: SD-SPI Write Protect Check Input bit #define SD_WE PORTCbits.RC13 //SD_WE PORTAbits.RA7 // Description: SD-SPI Write Protect Check TRIS bit #define SD_WE_TRIS TRISCbits.TRISC13 //SD_WE_TRIS TRISAbits.TRISA7 // Registers for the SPI module you want to use // Description: The main SPI control register #define SPICON1 SPI1CON1 // Description: The SPI status register #define SPISTAT SPI1STAT // Description: The SPI Buffer #define SPIBUF SPI1BUF // Description: The receive buffer full bit in the SPI status register #define SPISTAT_RBF SPI1STATbits.SPIRBF // Description: The bitwise define for the SPI control register (i.e. _____bits) #define SPICON1bits SPI1CON1bits // Description: The bitwise define for the SPI status register (i.e. _____bits) #define SPISTATbits SPI1STATbits // Description: The enable bit for the SPI module #define SPIENABLE SPISTATbits.SPIEN #define SPICON2 SPI2CON2 // Tris pins for SCK/SDI/SDO lines // Description: The TRIS bit for the SCK pin #define SPICLOCK TRISDbits.TRISD8 // Description: The TRIS bit for the SDI pin #define SPIIN TRISBbits.TRISB0 // Description: The TRIS bit for the SDO pin #define SPIOUT TRISBbits.TRISB1 #endif // Will generate an error if the clock speed is too low to interface to the card #if (GetSystemClock() < 100000) #error Clock speed must exceed 100 kHz #endif #elif defined __dsPIC33F__ // Description: SD-SPI Chip Select Output bit #define SD_CS LATBbits.LATB2 // Description: SD-SPI Chip Select TRIS bit #define SD_CS_TRIS TRISBbits.TRISB2 // Description: SD-SPI Card Detect Input bit #define SD_CD PORTAbits.RA2 // Description: SD-SPI Card Detect TRIS bit #define SD_CD_TRIS TRISAbits.TRISA2 // Description: SD-SPI Write Protect Check Input bit #define SD_WE PORTAbits.RA3 // Description: SD-SPI Write Protect Check TRIS bit #define SD_WE_TRIS TRISAbits.TRISA3 // Registers for the SPI module you want to use // Description: The main SPI control register #define SPICON1 SPI1CON1 // Description: The SPI status register #define SPISTAT SPI1STAT // Description: The SPI Buffer #define SPIBUF SPI1BUF // Description: The receive buffer full bit in the SPI status register #define SPISTAT_RBF SPI1STATbits.SPIRBF // Description: The bitwise define for the SPI control register (i.e. _____bits) #define SPICON1bits SPI1CON1bits // Description: The bitwise define for the SPI status register (i.e. _____bits) #define SPISTATbits SPI1STATbits // Description: The enable bit for the SPI module #define SPIENABLE SPISTATbits.SPIEN // Tris pins for SCK/SDI/SDO lines // Description: The TRIS bit for the SCK pin #define SPICLOCK TRISBbits.TRISB0 // Description: The TRIS bit for the SDI pin #define SPIIN TRISBbits.TRISB3 // Description: The TRIS bit for the SDO pin #define SPIOUT TRISBbits.TRISB1 #elif defined (__dsPIC33E__) || defined (__PIC24E__) // Description: SD-SPI Chip Select Output bit #define SD_CS LATBbits.LATB9 // Description: SD-SPI Chip Select TRIS bit #define SD_CS_TRIS TRISBbits.TRISB9 // Description: SD-SPI Analog/Digital Select ANSEL bit #define SD_CS_ANSEL ANSELBbits.ANSB9 // Description: SD-SPI Card Detect Input bit #define SD_CD PORTGbits.RG0 // Description: SD-SPI Card Detect TRIS bit #define SD_CD_TRIS TRISGbits.TRISG0 // Description: SD-SPI Write Protect Check Input bit #define SD_WE PORTGbits.RG1 // Description: SD-SPI Write Protect Check TRIS bit #define SD_WE_TRIS TRISGbits.TRISG1 // Description: SD-SPI Analog/Digital Select ANSEL bit #define SD_SCK_ANSEL ANSELGbits.ANSG6 #define SD_SDI_ANSEL ANSELGbits.ANSG7 #define SD_SDO_ANSEL ANSELGbits.ANSG8 // Description: The main SPI control register #define SPICON1 SPI2CON1 // Description: The SPI status register #define SPISTAT SPI2STAT // Description: The SPI Buffer #define SPIBUF SPI2BUF // Description: The receive buffer full bit in the SPI status register #define SPISTAT_RBF SPI2STATbits.SPIRBF // Description: The bitwise define for the SPI control register (i.e. _____bits) #define SPICON1bits SPI2CON1bits // Description: The bitwise define for the SPI status register (i.e. _____bits) #define SPISTATbits SPI2STATbits // Description: The enable bit for the SPI module #define SPIENABLE SPI2STATbits.SPIEN // Description: The definition for the SPI baud rate generator register #define SPIBRG SPI2BRG // Tris pins for SCK/SDI/SDO lines // Description: The TRIS bit for the SCK pin #define SPICLOCK TRISGbits.TRISG6 // Description: The TRIS bit for the SDI pin #define SPIIN TRISGbits.TRISG7 // Description: The TRIS bit for the SDO pin #define SPIOUT TRISGbits.TRISG8 #elif defined (__PIC32MX__) // Registers for the SPI module you want to use #define MDD_USE_SPI_1 //#define MDD_USE_SPI_2 //SPI Configuration #define SPI_START_CFG_1 (PRI_PRESCAL_64_1 | SEC_PRESCAL_8_1 | MASTER_ENABLE_ON | SPI_CKE_ON | SPI_SMP_ON) #define SPI_START_CFG_2 (SPI_ENABLE) // Define the SPI frequency #define SPI_FREQUENCY (20000000) #if defined MDD_USE_SPI_1 // Description: SD-SPI Chip Select Output bit #define SD_CS LATBbits.LATB1 // Description: SD-SPI Chip Select TRIS bit #define SD_CS_TRIS TRISBbits.TRISB1 // Description: SD-SPI Card Detect Input bit #define SD_CD PORTFbits.RF0 // Description: SD-SPI Card Detect TRIS bit #define SD_CD_TRIS TRISFbits.TRISF0 // Description: SD-SPI Write Protect Check Input bit #define SD_WE PORTFbits.RF1 // Description: SD-SPI Write Protect Check TRIS bit #define SD_WE_TRIS TRISFbits.TRISF1 // Description: The main SPI control register #define SPICON1 SPI1CON // Description: The SPI status register #define SPISTAT SPI1STAT // Description: The SPI Buffer #define SPIBUF SPI1BUF // Description: The receive buffer full bit in the SPI status register #define SPISTAT_RBF SPI1STATbits.SPIRBF // Description: The bitwise define for the SPI control register (i.e. _____bits) #define SPICON1bits SPI1CONbits // Description: The bitwise define for the SPI status register (i.e. _____bits) #define SPISTATbits SPI1STATbits // Description: The enable bit for the SPI module #define SPIENABLE SPICON1bits.ON // Description: The definition for the SPI baud rate generator register (PIC32) #define SPIBRG SPI1BRG // Tris pins for SCK/SDI/SDO lines // Tris pins for SCK/SDI/SDO lines #if defined(__32MX460F512L__) // Description: The TRIS bit for the SCK pin #define SPICLOCK TRISDbits.TRISD10 // Description: The TRIS bit for the SDI pin #define SPIIN TRISCbits.TRISC4 // Description: The TRIS bit for the SDO pin #define SPIOUT TRISDbits.TRISD0 #else // example: PIC32MX360F512L // Description: The TRIS bit for the SCK pin #define SPICLOCK TRISFbits.TRISF6 // Description: The TRIS bit for the SDI pin #define SPIIN TRISFbits.TRISF7 // Description: The TRIS bit for the SDO pin #define SPIOUT TRISFbits.TRISF8 #endif //SPI library functions #define putcSPI putcSPI1 #define getcSPI getcSPI1 #define OpenSPI(config1, config2) OpenSPI1(config1, config2) #elif defined MDD_USE_SPI_2 // Description: SD-SPI Chip Select Output bit #define SD_CS LATBbits.LATB9 // Description: SD-SPI Chip Select TRIS bit #define SD_CS_TRIS TRISBbits.TRISB9 // Description: SD-SPI Card Detect Input bit #define SD_CD PORTGbits.RG0 // Description: SD-SPI Card Detect TRIS bit #define SD_CD_TRIS TRISGbits.TRISG0 // Description: SD-SPI Write Protect Check Input bit #define SD_WE PORTGbits.RG1 // Description: SD-SPI Write Protect Check TRIS bit #define SD_WE_TRIS TRISGbits.TRISG1 // Description: The main SPI control register #define SPICON1 SPI2CON // Description: The SPI status register #define SPISTAT SPI2STAT // Description: The SPI Buffer #define SPIBUF SPI2BUF // Description: The receive buffer full bit in the SPI status register #define SPISTAT_RBF SPI2STATbits.SPIRBF // Description: The bitwise define for the SPI control register (i.e. _____bits) #define SPICON1bits SPI2CONbits // Description: The bitwise define for the SPI status register (i.e. _____bits) #define SPISTATbits SPI2STATbits // Description: The enable bit for the SPI module #define SPIENABLE SPI2CONbits.ON // Description: The definition for the SPI baud rate generator register (PIC32) #define SPIBRG SPI2BRG // Tris pins for SCK/SDI/SDO lines // Description: The TRIS bit for the SCK pin #define SPICLOCK TRISGbits.TRISG6 // Description: The TRIS bit for the SDI pin #define SPIIN TRISGbits.TRISG7 // Description: The TRIS bit for the SDO pin #define SPIOUT TRISGbits.TRISG8 //SPI library functions #define putcSPI putcSPI2 #define getcSPI getcSPI2 #define OpenSPI(config1, config2) OpenSPI2(config1, config2) #endif // Will generate an error if the clock speed is too low to interface to the card #if (GetSystemClock() < 100000) #error Clock speed must exceed 100 kHz #endif #endif #endif #ifdef USE_CF_INTERFACE_WITH_PMP /* CompactFlash-PMP card definitions: change these to fit your application when using the PMP module to interface with CF cards */ #ifdef __18CXX #error The PIC18 architecture does not currently support PMP interface to CF cards #elif defined __dsPIC30F__ // Sample dsPIC30 defines // Description: The output latch for the CF Reset signal #define CF_PMP_RST _RD0 // Description: The TRIS bit for the CF Reset signal #define CF_PMP_RESETDIR _TRISD0 // Description: The input port for the CF Ready signal #define CF_PMP_RDY _RD12 // Description: The TRIS bit for the CF Ready signal #define CF_PMP_READYDIR _TRISD12 // Description: The input port for the CF card detect signal #define CF_PMP_CD1 _RC4 // Description: The TRIS bit for the CF card detect signal #define CF_PMP_CD1DIR _TRISC4 #elif defined (__dsPIC33F__) || defined (__PIC24H__) || defined (__dsPIC33E__) || defined (__PIC24E__) // Sample dsPIC33 defines // Description: The output latch for the CF Reset signal #define CF_PMP_RST _RD0 // Description: The TRIS bit for the CF Reset signal #define CF_PMP_RESETDIR _TRISD0 // Description: The input port for the CF Ready signal #define CF_PMP_RDY _RD12 // Description: The TRIS bit for the CF Ready signal #define CF_PMP_READYDIR _TRISD12 // Description: The input port for the CF card detect signal #define CF_PMP_CD1 _RC4 // Description: The TRIS bit for the CF card detect signal #define CF_PMP_CD1DIR _TRISC4 #elif defined __PIC24F__ // Default case for PIC24F // Description: The output latch for the CF Reset signal #define CF_PMP_RST LATDbits.LATD0 // Description: The TRIS bit for the CF Reset signal #define CF_PMP_RESETDIR TRISDbits.TRISD0 // Description: The input port for the CF Ready signal #define CF_PMP_RDY PORTDbits.RD12 // Description: The TRIS bit for the CF Ready signal #define CF_PMP_READYDIR TRISDbits.TRISD12 // Description: The input port for the CF card detect signal #define CF_PMP_CD1 PORTCbits.RC4 // Description: The TRIS bit for the CF card detect signal #define CF_PMP_CD1DIR TRISCbits.TRISC4 #endif // Description: Defines the PMP data bus direction register #define MDD_CFPMP_DATADIR TRISE #endif #ifdef USE_MANUAL_CF_INTERFACE // Use these definitions with CF-Bit transaction.c and .h // This will manually perform parallel port transactions #ifdef __18CXX // Address lines // Description: The CF address bus output latch register (for PIC18) #define ADDBL LATA // Description: The CF address bus TRIS register (for PIC18) #define ADDDIR TRISA // Data bus // Description: The Manual CF data bus port register #define MDD_CFBT_DATABIN PORTD // Description: The Manual CF data bus output latch register #define MDD_CFBT_DATABOUT LATD // Description: The Manual CF data bus TRIS register #define MDD_CFBT_DATADIR TRISD // control bus lines // Description: The CF card chip select output latch bit #define CF_CE LATEbits.LATE1 // Description: The CF card chip select TRIS bit #define CF_CEDIR TRISEbits.TRISE1 // Description: The CF card output enable strobe latch bit #define CF_OE LATAbits.LATA5 // Description: The CF card output enable strobe TRIS bit #define CF_OEDIR TRISAbits.TRISA5 // Description: The CF card write enable strobe latch bit #define CF_WE LATAbits.LATA4 // Description: The CF card write enable strobe TRIS bit #define CF_WEDIR TRISAbits.TRISA4 // Description: The CF card reset signal latch bit #define CF_BT_RST LATEbits.LATE0 // Description: The CF card reset signal TRIS bit #define CF_BT_RESETDIR TRISEbits.TRISE0 // Description: The CF card ready signal port bit #define CF_BT_RDY PORTEbits.RE2 // Description: The CF card ready signal TRIS bit #define CF_BT_READYDIR TRISEbits.TRISE2 // Description: The CF card detect signal port bit #define CF_BT_CD1 PORTCbits.RC2 // Description: The CF card detect signal TRIS bit #define CF_BT_CD1DIR TRISCbits.TRISC2 #elif defined __dsPIC30F__ // Address lines // Description: The CF address bus bit 0 output latch definition (for PIC24/30/33/32) #define ADDR0 _LATB15 // Description: The CF address bus bit 1 output latch definition (for PIC24/30/33/32) #define ADDR1 _LATB14 // Description: The CF address bus bit 2 output latch definition (for PIC24/30/33/32) #define ADDR2 _LATG9 // Description: The CF address bus bit 3 output latch definition (for PIC24/30/33/32) #define ADDR3 _LATG8 // Description: The CF address bus bit 0 TRIS definition (for PIC24/30/33/32) #define ADRTRIS0 _TRISB15 // Description: The CF address bus bit 1 TRIS definition (for PIC24/30/33/32) #define ADRTRIS1 _TRISB14 // Description: The CF address bus bit 2 TRIS definition (for PIC24/30/33/32) #define ADRTRIS2 _TRISG9 // Description: The CF address bus bit 3 TRIS definition (for PIC24/30/33/32) #define ADRTRIS3 _TRISG8 // Data bus // Description: The Manual CF data bus port register #define MDD_CFBT_DATABIN PORTE // Description: The Manual CF data bus output latch register #define MDD_CFBT_DATABOUT PORTE // Description: The Manual CF data bus TRIS register #define MDD_CFBT_DATADIR TRISE // control bus lines // Description: The CF card chip select output latch bit #define CF_CE _RD11 // Description: The CF card chip select TRIS bit #define CF_CEDIR _TRISD11 // Description: The CF card output enable strobe latch bit #define CF_OE _RD5 // Description: The CF card output enable strobe TRIS bit #define CF_OEDIR _TRISD5 // Description: The CF card write enable strobe latch bit #define CF_WE _RD4 // Description: The CF card write enable strobe TRIS bit #define CF_WEDIR _TRISD4 // Description: The CF card reset signal latch bit #define CF_BT_RST _RD0 // Description: The CF card reset signal TRIS bit #define CF_BT_RESETDIR _TRISD0 // Description: The CF card ready signal port bit #define CF_BT_RDY _RD12 // Description: The CF card ready signal TRIS bit #define CF_BT_READYDIR _TRISD12 // Description: The CF card detect signal port bit #define CF_BT_CD1 _RC4 // Description: The CF card detect signal TRIS bit #define CF_BT_CD1DIR _TRISC4 #elif defined (__dsPIC33F__) || defined (__PIC24H__) || defined (__dsPIC33E__) || defined (__PIC24E__) // Address lines // Description: The CF address bus bit 0 output latch definition (for PIC24/30/33/32) #define ADDR0 _LATB15 // Description: The CF address bus bit 1 output latch definition (for PIC24/30/33/32) #define ADDR1 _LATB14 // Description: The CF address bus bit 2 output latch definition (for PIC24/30/33/32) #define ADDR2 _LATG9 // Description: The CF address bus bit 3 output latch definition (for PIC24/30/33/32) #define ADDR3 _LATG8 // Description: The CF address bus bit 0 TRIS definition (for PIC24/30/33/32) #define ADRTRIS0 _TRISB15 // Description: The CF address bus bit 1 TRIS definition (for PIC24/30/33/32) #define ADRTRIS1 _TRISB14 // Description: The CF address bus bit 2 TRIS definition (for PIC24/30/33/32) #define ADRTRIS2 _TRISG9 // Description: The CF address bus bit 3 TRIS definition (for PIC24/30/33/32) #define ADRTRIS3 _TRISG8 // Data bus // Description: The Manual CF data bus port register #define MDD_CFBT_DATABIN PORTE // Description: The Manual CF data bus output latch register #define MDD_CFBT_DATABOUT PORTE // Description: The Manual CF data bus TRIS register #define MDD_CFBT_DATADIR TRISE // control bus lines // Description: The CF card chip select output latch bit #define CF_CE _RD11 // Description: The CF card chip select TRIS bit #define CF_CEDIR _TRISD11 // Description: The CF card output enable strobe latch bit #define CF_OE _RD5 // Description: The CF card output enable strobe TRIS bit #define CF_OEDIR _TRISD5 // Description: The CF card write enable strobe latch bit #define CF_WE _RD4 // Description: The CF card write enable strobe TRIS bit #define CF_WEDIR _TRISD4 // Description: The CF card reset signal latch bit #define CF_BT_RST _RD0 // Description: The CF card reset signal TRIS bit #define CF_BT_RESETDIR _TRISD0 // Description: The CF card ready signal port bit #define CF_BT_RDY _RD12 // Description: The CF card ready signal TRIS bit #define CF_BT_READYDIR _TRISD12 // Description: The CF card detect signal port bit #define CF_BT_CD1 _RC4 // Description: The CF card detect signal TRIS bit #define CF_BT_CD1DIR _TRISC4 #elif defined __PIC24F__ // Address lines // Description: The CF address bus bit 0 output latch definition (for PIC24/30/33/32) #define ADDR0 LATBbits.LATB15 // Description: The CF address bus bit 1 output latch definition (for PIC24/30/33/32) #define ADDR1 LATBbits.LATB14 // Description: The CF address bus bit 2 output latch definition (for PIC24/30/33/32) #define ADDR2 LATGbits.LATG9 // Description: The CF address bus bit 3 output latch definition (for PIC24/30/33/32) #define ADDR3 LATGbits.LATG8 // Description: The CF address bus bit 0 TRIS definition (for PIC24/30/33/32) #define ADRTRIS0 TRISBbits.TRISB15 // Description: The CF address bus bit 1 TRIS definition (for PIC24/30/33/32) #define ADRTRIS1 TRISBbits.TRISB14 // Description: The CF address bus bit 2 TRIS definition (for PIC24/30/33/32) #define ADRTRIS2 TRISGbits.TRISG9 // Description: The CF address bus bit 3 TRIS definition (for PIC24/30/33/32) #define ADRTRIS3 TRISGbits.TRISG8 // Data bus // Description: The Manual CF data bus port register #define MDD_CFBT_DATABIN PORTE // Description: The Manual CF data bus output latch register #define MDD_CFBT_DATABOUT PORTE // Description: The Manual CF data bus TRIS register #define MDD_CFBT_DATADIR TRISE // control bus lines // Description: The CF card chip select output latch bit #define CF_CE PORTDbits.RD11 // Description: The CF card chip select TRIS bit #define CF_CEDIR TRISDbits.TRISD11 // Description: The CF card output enable strobe latch bit #define CF_OE PORTDbits.RD5 // Description: The CF card output enable strobe TRIS bit #define CF_OEDIR TRISDbits.TRISD5 // Description: The CF card write enable strobe latch bit #define CF_WE PORTDbits.RD4 // Description: The CF card write enable strobe TRIS bit #define CF_WEDIR TRISDbits.TRISD4 // Description: The CF card reset signal latch bit #define CF_BT_RST PORTDbits.RD0 // Description: The CF card reset signal TRIS bit #define CF_BT_RESETDIR TRISDbits.TRISD0 // Description: The CF card ready signal port bit #define CF_BT_RDY PORTDbits.RD12 // Description: The CF card ready signal TRIS bit #define CF_BT_READYDIR TRISDbits.TRISD12 // Description: The CF card detect signal port bit #define CF_BT_CD1 PORTCbits.RC4 // Description: The CF card detect signal TRIS bit #define CF_BT_CD1DIR TRISCbits.TRISC4 #endif #endif //#include #endif